Elcometer 345 Coating Thickness Gauge - 2 Key SSG

The Elcometer 345 Digital Coating Thickness Gauge has a small rugged design combined with a clear and easy to read digital display enabling this gauge to be used in numerous environments.

Simple, left or right handed operation
Automatic switch on and off
Protected calibration
For coatings on steel substrates
Switchable between microns & mils
Signals audibly when readings are taken
Ideal gauge for steel inspection
Includes "Zero Offset" for negating surface roughness automatically
Water and spray proof cover available

Elcometer 345 Coating Thickness Gauge - 4 Key

The Elcometer 345 Digital Coating Thickness Gauge has a small rugged design combined with a clear and easy digital display enable this gauge to be used in numerous environments.

Simple Statistics
1% Accuracy (1-3% over full range, 1% when calibrated close to reading to be measured)
Fast Reading Rate
"Big Foot" for stability on integral models
Simple and easy to use with Keylock to avoid accidental re-calibration
2 point calibration gives increased precision
Withstands rough handling and supplied with a special hard wearing probe tip
Measures on flat, curved and round substrates
Switchable between microns or mm & mils
Integral and separate probe options available

Elcometer 456 Coating Thickness Gauge

The recently introduced Elcometer 456 is perhaps the most advanced coating thickness gauge on the market today, here are just some of the new features:

Full Menu Driven Display - in the following languages -
English, Chinese, Czech, Danish, Dutch, Farsi, French, German, Greek, Hebrew, Italian, Japanese, Korean, Portuguese, Russian, Slovenian, Spanish, Swedish and Norwegian
High Speed Accurate Readings - greater than 60 per minute
Three Model Options - Basic, Standard, Top
Interchangeable Probes - including the NEW PLUG IN INTEGRAL PROBES
Standard and Predefined calibration Options
Free Analysis Software* provided
Both IR and Cable* Data Output

Elcometer 355 Coating Thickness System

Available in two model versions, this true state of the art hand-held measuring system is packed with time-saving and cost-cutting features.
True 1% Accuracy
Flexible Probe Modular System
Printer or PC Output
Statistical Analysis
Rugged Aluminium Case
Traceable Thickness Standards
Conforms to BS, ISO DIN, ASTM & SSPC methods of measurement

Elcometer 365 SPC Coating Thickness Gauge System

Over the past few years coating specifications have become more of a requirement resulting in a need for greater control throughout the coating process.

The Elcometer 365 has been designed to provide a controlled method of coating inspection - thereby allowing the user to monitor the coating process, statistically.

The data generated by the Elcometer 365 can alert the operator to alter the process before the coating parameters have been exceeded - avoiding costly re-work.

1% Accuracy over a wide range of probe modules
Menu Driven Keyboard
Process Capability Cp, Cpk
FORD, ISO, AT&T Warnings
Fully Networkable
Datastat SPC Software and EDTS Excel Link Software compatible for further computer analysis and data storage
On screen charting: Histogram, Xbar and Range charts
FNF Capability
Real SPC Data Collection in a Coating Thickness Gauge
User Definable Batch Names (Alpha-numerical)
Password Protection
High and Low Reasonable Limits
Average and Counted Average Mode
RS232 Printer/PC Output - Serial & Parallel
Rugged Aluminum Case
Traceable Thickness Standards
Date and Time
Conforms to BS, ISO DIN, ASTM & SSPC methods of measurement

Elcometer 101 Coating Thickness Gauge

Elcometer 101 Coating Thickness Gauge

The Elcometer 101 is the world's first portable coating thickness gauge and is still in production. Developed , patented and first produced in 1947, this gauge is now written into many world-wide specifications and standards, and today still incorporates advantages over other gauges.

Insensitive to hot and cold coatings or surfaces - ideal for hot sprayed metal coatings for immediate results
Wide choice of scales
Can be used in any orientation
Incorporates reading hold
Foils supplied to check calibration
Accuracy better than 10%

Elcometer 211 Coating Thickness Gauge

The Elcometer 211, commonly referred to as the "Banana Gauge," has proven to be a successful coating thickness gauge where the use of electronic instruments is difficult, i.e. inflammable atmospheres in oil and gas production.

The "v" grooved base, rubber feet and clear scale with its ranges for thicker coatings, make this instrument one of the most popular mechanical gauges in the world.

Ideal for underwater coatings inspection and other hazardous areas
Ideal for very cold surfaces
Factory calibrated
Small, portable
Foils supplied to check calibration on the jobsite
Accuracy +/- 5%
As this product does not contain batteries it is ideal for hazardous areas

Elcometer 157 Coating Thickness Gauge

This simple pull-off gauge is a top pocket, lightweight, foreman's-type gauge for spot check indications of coating thickness.

Insensitive to hot and cold coatings or surfaces - ideal for hot sprayed metal coatings for immediate results
Easy to use and light weight
3 Scales on the instrument body
Pre-calibrated with no adjustment required
Accuracy 15%

Elcometer 141 Paint Inspection Gauge

Destructive thickness measurement is not only often the only guaranteed method available to test vertain coating/substrate combinations such as paint applied to concrete, wood, plaster etc, but also the only method to identify individual layer thicknesses of a multi-layer coating system.

The Elcometer 141 PIG offers a quick, versatile method of coating examination and measurement in a portable, easy to use instrument. Ergonomically designed to give a balanced weight distribution for a more consistent cut.
Large easy to grip handle - allows the operator to cut thick or hard coatings easily
Internal cutter storage compartment
x50 magnification direct measurement mircoscope
Metric and Imperial Versions
Can be adapted into the Elcometer 107 Cross Hatch Cutter

Elcometer 121 Paint Inspection Gauge and Elcometer 121/2 Universal PIG

For some combinations of coating and substrate it is necessary to use a destructive measurement method. The Elcometer 121 & 121/2 Paint Inspection Gauges are designed for this application.

Battery powered illumination with the built-in microscope
Fully portable and robust
The Elcometer 121/2 Universal PIG (shown here on the right) provides the user not only with a PIG but also:

Cross Hatch Cutter - for coating adhesion
Buchholz Hardness Tester - to measure coating hardness

Elcometer 195 Saberg Drill and Elcometer 126 Dial Thickness Gauge

For some combinations of coating and substrate it is necessary to use a destructive measurement method. Whereas the Paint Inspection Gauges (PIG) make a cut along the coating, the Elcometer Saberg Drill makes a small hole to measure the individual coating layer thicknesses of a multi-layer coating.

Minimal coating damage during test

Fully portable and robust
Measures coatings up to 1500 microns (60 mil)
Used in conjunction with gradicule scale microscope or the Elcometer 126 Dial Inspection Gauge
Elcometer 126 Dial Inspection Gauge

This portable , easy to use instrument has a broad based foot and is fitted with a hard tip. The tip is placed a hole or the hole generated by the Elcometer 195 and the dial indicates the coating thickness.

Can be used in accordance with BS EN 3900-CS-5B, ISO 2808-5B, ASTM D4138.