Pit
Depth Gauges
 aaaaaaaaaaaa
4486-D
Gauge Type: Pit Depth
Gauge
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.001"
Dial Travel: 1/2"
Anvil: 2-1/8" long, hardened steel with "V" cross
section, Dial Face parallel to thread axis.
Description: The 4486-D is used to measure pits
and scratches that appear on the surface of pipe
and is normally equipped with a 40 Degree Cone Point.
Calibration of UST notches can also be achieved
by substituting the normal cone point with the SP
12015 or the DP 12012.
SP 12015/Swivel Point:
Specially designed contact
for calibration of ultrasonic test grooves.
Full 360° rotation allows for easy depth check on
longitudinal and tangential notches. Used
with #4486-D.
4486-A
Gauge Type: Pit Depth Gauge
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.001"
Dial Travel: 1/2"
Anvil: 12" long, hardened tool steel with flat base,
Dial Face parallel to thread axis.
Description: The 4486-A is
used to measure indentations left in the pipe surface
from the rolling and straightening processes. This
gauge is normally equipped with a 40 Degree Cone
Point but will accept standard Tungsten Carbide
contact points.
4486-C
Gauge Type: Pit Depth Gauge
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.001"
Dial Travel: 1/2"
Anvil: 6" long, hardened tool steel with flat base,
Dial Face parallel to thread axis.
Description: The 4486-C is used to measure pits
scratches and indentations that appear on the surface
of pipe. This gauge is normally equipped with a
40 Degree Cone Point but will accept standard Tungsten
Carbide contact points.
4486-B
Gauge Type: Pit Depth Gauge
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.001"
Dial Travel: 1/2"
Anvil: 8" long, hardened tool steel with flat base,
Dial Face parallel to thread axis.
Description: The 4486-B is used to measure pits
scratches and indentations that appear on the surface
of pipe. This gauge is normally equipped with a
40 Degree Cone Point but will accept standard Tungsten
Carbide contact points.
4486-F
Gauge Type: Pit Depth Gauge
Dial Type: 0-10-0, Balanced w/ Revolution Counting
Hand
Graduation: 0.001"
Dial Travel: 1/8"
Anvil: 1" diameter, hardened tool steel with flat
base.
Description: The 4486-F Pit Depth Gauge is used
to measure the depth of relief forms in flat rolled
stock. This gauge is normally equipped with a 40
Degree Cone Point but will accept standard Tungsten
Carbide contact points.
4486-D/M
Gauge Type: Pit Depth Gauge,
Metric
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.02mm
Dial Travel: 12mm
Anvil: 54mm long, hardened steel with "V" cross
section, Dial Face parallel to thread axis.
Description: The 4486-D/M is used to measure pits
and scratches that appear on the surface of pipe
and is normally equipped with a 40 Degree Cone Point.
Calibration of UST notches can also be achieved
by substituting the normal cone point with the SP
12015 or the DP 12012.
4486-A/M
Gauge Type: Pit Depth Gauge,
Metric
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.02mm
Dial Travel: 12mm
Anvil: 304mm long, hardened tool steel with flat
base, Dial Face parallel to thread axis.
Description: The 4486-A/M is used to measure indentations
left in the pipe surface from the rolling and straightening
processes. This gauge is normally equipped with
a 40 Degree Cone Point but will accept standard
Tungsten Carbide contact points.
4486-C/M
Gauge Type: Pit Depth Gauge,
Metric
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.02mm
Dial Travel: 12mm
Anvil: 152mm long, hardened tool steel with flat
base, Dial Face parallel to thread axis.
Description: The 4486-C/M is used to measure pits
scratches and indentations that appear on the surface
of pipe. This gauge is normally equipped with a
40 Degree Cone Point but will accept standard Tungsten
Carbide contact points.
4486-B/M
Gauge Type: Pit Depth Gauge,
Metric
Dial Type: 0-100, Counter-Clockwise
Graduation: 0.02mm
Dial Travel: 12mm
Anvil: 203mm long, hardened tool steel with flat
base, Dial Face parallel to thread axis.
Description: The 4486-B/M is used to measure pits
scratches and indentations that appear on the surface
of pipe. This gauge is normally equipped with a
40 Degree Cone Point but will accept standard Tungsten
Carbide contact points.
4486-F/M
Gauge Type: Pit Depth Gauge,
Metric
Dial Type: 0~50~0, Balanced dial w/ Revolution Counting
Hand
Graduation: 0.01mm
Dial Travel: 3mm
Anvil: 25mm diameter, hardened tool steel with flat
base.
Description: The 4486-F/M Pit Depth Gauge is used
to measure the depth of relief forms in flat rolled
stock. This gauge is normally equipped with a 40
Degree Cone Point but will accept standard Tungsten
Carbide contact points.
|
